UP 00:00:00TIME --:--NET [ONLINE]

room --measure

Room Measurement Tool

How to use
  1. Draw the outline of the room, or pick a shape.
  2. Type the length of each wall you measured.
  3. Get the area and a floor plan.

Sketch a room, enter the walls you measured and get its floor area and a floor plan.

Draw the outline of your room in one stroke, going all the way round, with your finger or mouse. The tool squares up the corners. Rooms with right-angled corners only.

Or start from a shape

Learn more

How to use the room measurement tool

  1. Draw the room. Trace its outline in one stroke, all the way round, with your finger or mouse. The tool squares up the corners and labels each wall A, B, C and so on. If you would rather not draw, pick a rectangle, L, T or U shape.
  2. Enter the walls you measured. Tap a wall on the plan, or use the boxes. You can type 12' 6", 12.5, 150 in, 3.5 m or 350 cm.
  3. Watch the plan firm up. It tells you how many more walls it needs. Walls it works out for itself are marked calculated. Once everything is known, the outline turns solid and drawn to scale.
  4. Add the ceiling height if you want the volume and wall area as well.
  5. Save it. Download the floor plan as a picture, copy the numbers, or email both to yourself.

Your drawing and measurements are saved in this browser, so a refresh does not lose them. Draw a different room starts again.

How to measure a room

  • Measure each wall along the floor, from corner to corner, with the tape held straight and level.
  • Do not assume opposite walls match. Rooms are rarely perfectly square. Measuring both is a good check, because the tool will say if the numbers do not fit together.
  • Decide what you are measuring. For flooring you usually measure wall to wall. Built-in cupboards, chimney breasts and alcoves change the shape, so draw them as part of the outline.
  • Measure twice and round to the nearest quarter inch or centimetre. That is as precise as the results are shown.
  • Check before you buy. Ask your supplier how much extra to allow for cuts and waste, and confirm the final measurements on site.

How the area is worked out

In a room with only right-angled corners every wall runs left, right, up or down. For the outline to close, the walls that run right must add up to the walls that run left, and the walls that run down must add up to the walls that run up. That gives one equation for each direction, so once all but one wall in a direction is known, the last one is fixed.

A rectangle has four walls and needs two measurements. An L-shape has six walls and needs four. In general a room with n walls needs n minus 2.

The area is then found from the corners of the finished outline, which works for any shape with straight walls: rectangles, L, T and U shapes and anything else you can draw. One square metre is 10.7639 square feet. With a ceiling height, the volume is the floor area times the height, and the wall area is the perimeter times the height before taking off doors and windows.

If every wall is entered and the totals are slightly out, as they usually are with a tape measure, the plan is adjusted by up to about 2 inches (6 cm) in total and the tool tells you how much. A larger gap is reported as a mistake.

Frequently asked questions

How do I calculate the square footage of a room?

Multiply the length by the width. A room that is 12 ft by 15 ft is 180 square feet. For an L-shaped or other right-angled room, split it into rectangles, work out each one and add them up. This tool does that for you from the wall lengths.

How do I convert square feet to square metres?

Divide square feet by 10.7639 to get square metres, so 180 ft² is 16.72 m². Multiply square metres by 10.7639 to go the other way.

Why do I only have to measure some of the walls?

In a right-angled room the walls that run left must add up to the walls that run right, and the walls that run up must add up to the walls that run down. Once you have entered all but one wall in a direction, the last one is fixed, so the tool works it out. A room with n walls needs n minus 2 measurements: 2 for a rectangle, 4 for an L-shape.

What if my measurements do not add up?

Real walls are rarely perfectly square. If the totals differ by less than about 2 inches (6 cm) the tool adjusts the plan slightly and tells you. A bigger gap means a number is probably wrong, and the tool points to the walls to check.

Does it work for angled or curved walls?

No. It handles rooms whose walls all meet at right angles: rectangles and L, T and U shapes, and anything else made of straight walls at 90 degrees. For an angled corner, measure the room as a right-angled shape and add or subtract the triangle by hand.

Is the floor plan to scale?

Yes, once every wall is known it is drawn from your lengths. Until then the dashed outline is only a guess based on your sketch.

How accurate are the results?

As accurate as the lengths you type in. Lengths are shown to the nearest quarter inch or centimetre. Check important measurements on site, and ask your supplier how much extra to allow before ordering flooring or paint.

Is my drawing saved or sent anywhere?

The drawing and measurements stay in your browser, saved on your device so a refresh does not lose them. They are only sent if you use the email button, and then only to send that one email. They are not stored on our server.